2018 Land Pride RC2515

Call for Price

Land Pride



The new RC2515, a 15' version of our popular 12' medium-duty Rotary Cutter, is an economical solution for general grass cutting needs. The Land Pride gearboxes feature a 1-5/8" output shaft and stout lower bearings. The gearboxes are driven by a constant velocity Cat. 4 main driveline and Cat. 3 connecting drivelines with slip-clutch protection on all three. The ride is cushioned by a deck-mounted spring and can be enhanced with optional 29" used aircraft tires – either 4 or 6 per cutter.

  • Surpassed rugged industry standards: All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures.
  • Factory assembled: Saves customer set-up time and money.
  • 5 Year gearbox warranty: Shows confidence in gearbox integrity.
  • 160 hp Divider gearbox and 75 hp wing gearboxes: A rugged heavy built gearboxes capable of handling heavy cutting applications.
  • Gearbox seal protection: Gearbox bottom seal protection for longer bearing life.
  • Input driveline: Cat. 4 CV: Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.
  • Easy greasable drivelines: Drivelines have access holes for greasing the U-joints and to grease the inner profiles.
  • 2 Plate slip-clutch: Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered.
  • 15,000 fpm high blade tip speed: Allows clean cutting of material and even distribution.
  • 6" Blade overlap: Eliminates skipping during turns.
  • 11 1/4" Deck height: Handles heavy cutting, which reduces balling-up of cut material under the deck.
  • 3/16" Gauge Stump jumper backed with a 1" thick mounting bar: Allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal.
  • 10 Gauge smooth deck top: Reduces accumulation of debris and is easier and faster to clean.
  • 1/4" Plate side skirt: Reduces debris piercing possibilities.
  • Low hitch weight: Less drawbar wear. Less ballast required. Works well with lighter tractors.
  • Dual remote hydraulics: Easy to operate. Fits most tractors, only two duplex outlets required to lift wings and change cutting height separately.
  • Hinged wing sections: Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches and hollows can cause uneven cutting. Wings will hinge 20o down.
  • 7/8" Solid hinge rods: Gives great strength to the cutter from front to rear, and in the hinge area itself.
  • Wing transport locks: Holds transport wings in the folded-up position in case of hydraulic pressure loss.
  • Enclosed front to rear dual leveling rods: Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod.
  • 5-Bolt hubs: 5-Bolt hubs makes the wheel assembly more durable and longer lasting.
  • Drain holes in wheel rims: Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.
  • Spring-cushioned lift cylinder: Cushions loads on drawbar.
  • Replaceable wheel spindles: Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove two bolts to replace damaged spindle.
  • 7/8" Leveling rods: Large diameter leveling rods provide superior supporting strength over rough terrain.
  • Airplane tires: Gives better cushion while transporting and provides flotation in soft ground.
  • PTO Horsepower: 50-100 hp
  • Gearbox Horsepower: Splitter: 160 hp
  • Gearbox Horsepower: Center & Wings: 75 hp
  • Gearbox Shafts: Input Shaft: 1 3/8 in. 6 Spline
  • Gearbox Shafts: Output Shaft: 1 5/8 in.
  • Gear Box Capacity & Lubrication: Splitter: 4.5 pints of gear lube 80-90W EP
  • Gear Box Capacity & Lubrication: Center & Wings: 5.75 pints of gear lube 80-90W EP
  • Cutting Capacity: 1 1/2 in.
  • Hitch Weight: 1,022 lb.
  • Machine Weight: 3,202 lb. with chain guards & four laminated tires
  • Blade Tip Speed At 540 RPM: Center Blades & Wing Blades = 14,963 FPM
  • Hitch Types: Pull-type hitch & clevis
  • Hitch Jack: Standard (2,000 lb.)
  • Cutting Width: 15 ft. 0 in.
  • Overall Width: 15 ft. 7 in.
  • Normal Transport Width: 10 ft. 2 1/2 in. with transport locks set and cutting blade 13 in. off the ground.
  • Minimum Transport Width: 8 ft. 4 in. with transport locks set and cutting blade 2 in. off the ground.
  • Overall Length: 15 ft. 2 in. with laminated tires; 15 ft. 5 1/2 in. with aircraft tires
  • Deck Height: 11 1/4 in.
  • Cutting Height: 2 in. to 13 in.
  • Lift Hydraulics: 2 1/2 in. x 8 in. hydraulic cylinder, hoses, fittings & stroke control spacers
  • Wing Hydraulics: 2 1/2 in. x 10 in. hydraulic cylinders, hoses & fittings
  • Wing Transport Protection: Wing transport locks
  • Deck Material: 10 Gauge deck
  • Side Skirt Material: 1/4 in. Plate
  • Skid Shoes: Wing Deck: 1 replaceable shoe per wing; Center Deck: 2 replaceable shoes
  • Blade Rotation: Left Wing: Clockwise
  • Blade Rotation: Center Deck: Counterclockwise
  • Blade Rotation: Right Wing: Counterclockwise
  • Blades - 6 (2 per deck): 1/2 in. x 4 in. Heat Treated Free Swinging Alloy Steel with up lift
  • Blade Overlap: 6 in.
  • Blade Bolt: Keyed with hardened flat washer & lock nut
  • Stump Jumper / Blade Holder: 10 Gauge round dish shaped pan, reinforced with 1 in. x 4 in. blade bar
  • Front & Rear Guards: Single chain or rubber
  • Input Driveline: ASAE Category 4 with constant velocity u-joint
  • Intermediate & Wing Drivelines: ASAE Category 3 with slip-clutch
  • Wheels: 29 in. Used aircraft tires or 21 in. laminated wheels
  • Number of Wheels: 4 or 6 Total
  • Transport Axle: Spring-cushioned lift cylinder
  • Hubs: Cast iron five-bolt hubs with tapered roller bearings and 1 3/4 in. shafts.
  • Colors: Standard color: Beige; Optional colors: Green, Orange, or Red



Working Width
15 ft.
15 ft. 7 in.
15 ft. 2 in.
3,202 lb.
Recommended HP
50-100 PTO hp

Related Products